C.E. Smith
C.E. Smith 27646 Pvc Post Guide-Ons, 60", Black - 27646 - 618-27646F1
Allows you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. Mounting hardware included. Sold in pairs. Adjusts out to 13" each Side Fits Frames up to 3" W x 4-1/4" HMade in the USAFor larger trailer frames check out our Large Frame U-Bolt Kit (11416).Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The galvanized coating is very thin (0.45 oz. on each side).Check with your state Department of Transportation for restrictions regarding maximum trailer width.
C.E. Smith 27647 Pvc Post Guide-Ons, 40", 75 Degree Bend, Black - 27647 - 618-27647F1
Visual markers when backing trailers down the rampFits frames up to 3" wide by 4-1/4" tallMetal uprights allow for 13" of side adjustment1-1/2"Square 16 ga. pre-galvanized steel uprights
C.E. Smith 27660 2' Bunkboard Guide-Ons - 27660 - 618-27660F1
Carpeted bunkboards provide proper center loading even in wind or side current conditions. Can be mounted on top of frame for extra heightHeight of 21'' with adjustment out to 13" from frame on each sideBoards tilt to hug the hull covered with high grade marine carpet and are untreated Southern yellow pine1-1/2" square pre-galvanized uprights, angled out at 75°
C.E. Smith 27670 Pontoon Pvc Post Guide-Ons - 27670 - 618-27670F1
These guide-ons mount on top of rear cross member and fit in between the pontoons to center your boat on the trailer. Mounting hardware included. Sold in pairs. Fit up to 3" W x 4-1/4" H frames. 1-1/2" square 16 gauge pre-galvanized steel uprights. 2-3/8" diameter white PVC posts.
C.E. Smith 27671 Pontoon Bunkboard Guide-Ons - 27671 - 618-27671F1
Ideal for bunk style pontoon boat trailer with box, channel, or I-beam frames up to 3" wide x 4-1/4" tall. Pontoon glides easily past the carpeted bunk boards guiding the pontoon boat onto the trailer. Height is adjustable and is set during install between 24" and 36" above trailer frame. Mount with bunks 2-3" from pontoons on a trailer frame cross member. Galvanized steel construction. Zinc plated hardware. Includes two 24" carpeted bunk boards AND U-bolt mounting brackets.
C.E. Smith 27740 Led Lighted Pvc Post Guide-Ons, 40" - 27740 - 618-27740F1
Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. Mounting hardware and wiring included. Sold in pairs. Fits Frames up to 3" W x 4-1/4" H1-1/2" square, 16 gauge pre-galvanized steel uprightsMade in the USAFor larger trailer frames check out our Large Frame U-Bolt Kit (11416).Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The galvanized coating is very thin (0.45 oz. on each side).
C.E. Smith 27760 Led Lighted Pvc Post Guide-Ons, 60" - 27760 - 618-27760F1
Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. Mounting hardware and wiring included. Sold in pairs. Fits Frames up to 3" W x 4-1/4" H1-1/2" square, 16 gauge pre-galvanized steel uprightsMade in the USAFor larger trailer frames check out our Large Frame U-Bolt Kit (11416).Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The galvanized coating is very thin (0.45 oz. on each side).
C.E. Smith 30250 Trailer Tongue Step Pad, 25" X 9" - 30250 - 618-30250F1
Makes accessing your boat easy, providing a stable and steady place to anchor your feet. It can be mounted anywhere that is suitable on trailer tongues or side rails. Fits any 2x3" or 3x3" rail, mounting hardware included. Has a textured surface for slip resistance. Sold individually
C.E. Smith 53670A 70 Series Flush Mount Rod Holders, Bar, 0 Degree - 53670A - 618-53670Af1
Feature a wide low profile cap for excellent mounting strength and to enhance the appearance of any boat. 100% welded cap to tube joint will never break. Super tough 1/4" wide x 1/2" tall gimbal bar will stand up to virtually any punishment heavy tackle or downrigger mounts can dish out. White vinyl liner protects rods and is keyed with the gimbal bar to eliminate liner twist. White liner color316L Stainless steel1-5/8" Inner diameter, Fits 2-3/16" hole diameter1/4" wide x 1/2" wide gimbal bar9" Tube length
C.E. Smith 53670Ca 70 Series Flush Mount Rod Holders, Cast, 0 Degree - 53670Ca - 618-53670Caf1
Feature a wide low profile cap for excellent mounting strength and to enhance the appearance of any boat. 100% welded cap to tube joint will never break. Super tough 1/4" wide x 1/2" tall gimbal bar will stand up to virtually any punishment heavy tackle or downrigger mounts can dish out. White vinyl liner protects rods and is keyed with the gimbal bar to eliminate liner twist. White liner color316L Stainless steel1-5/8" Inner diameter, Fits 2-3/16" hole diameter1/4" wide x 1/2" wide gimbal bar9" Tube length
C.E. Smith 53671A 70 Series Flush Mount Rod Holders, Bar, 15 Degree - 53671A - 618-53671Af1
Feature a wide low profile cap for excellent mounting strength and to enhance the appearance of any boat. 100% welded cap to tube joint will never break. Super tough 1/4" wide x 1/2" tall gimbal bar will stand up to virtually any punishment heavy tackle or downrigger mounts can dish out. White vinyl liner protects rods and is keyed with the gimbal bar to eliminate liner twist. White liner color316L Stainless steel1-5/8" Inner diameter, Fits 2-3/16" hole diameter1/4" wide x 1/2" wide gimbal bar9" Tube length
C.E. Smith 53671Ca 70 Series Flush Mount Rod Holders, Cast, 15 Degree - 53671Ca - 618-53671Caf1
Feature a wide low profile cap for excellent mounting strength and to enhance the appearance of any boat. 100% welded cap to tube joint will never break. Super tough 1/4" wide x 1/2" tall gimbal bar will stand up to virtually any punishment heavy tackle or downrigger mounts can dish out. White vinyl liner protects rods and is keyed with the gimbal bar to eliminate liner twist. White liner color316L Stainless steel1-5/8" Inner diameter, Fits 2-3/16" hole diameter1/4" wide x 1/2" wide gimbal bar9" Tube length
C.E. Smith 53672A 70 Series Flush Mount Rod Holders, Bar, 30 Degree - 53672A - 618-53672Af1
Feature a wide low profile cap for excellent mounting strength and to enhance the appearance of any boat. 100% welded cap to tube joint will never break. Super tough 1/4" wide x 1/2" tall gimbal bar will stand up to virtually any punishment heavy tackle or downrigger mounts can dish out. White vinyl liner protects rods and is keyed with the gimbal bar to eliminate liner twist. White liner color316L Stainless steel1-5/8" Inner diameter, Fits 2-3/16" hole diameter1/4" wide x 1/2" wide gimbal bar9" Tube length
C.E. Smith 53672Ca 70 Series Flush Mount Rod Holders, Cast, 30 Degree - 53672Ca - 618-53672Caf1
Feature a wide low profile cap for excellent mounting strength and to enhance the appearance of any boat. 100% welded cap to tube joint will never break. Super tough 1/4" wide x 1/2" tall gimbal bar will stand up to virtually any punishment heavy tackle or downrigger mounts can dish out. White vinyl liner protects rods and is keyed with the gimbal bar to eliminate liner twist. White liner color316L Stainless steel1-5/8" Inner diameter, Fits 2-3/16" hole diameter1/4" wide x 1/2" wide gimbal bar9" Tube length
C.E. Smith 53673A Backing Plate, 70 Series - 53673A - 618-53673Af1
Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. Regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Available for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Use your 1/4" stainless bolts and nuts (hardware not included).
C.E. Smith 53680Ca 80 Series Flush Mount Rod Holders, Cast, 0 Degree - 53680Ca - 618-53680Caf1
White liner color316L Stainless steel1-7/8" Inner diameter Fits 2-1/2" hole diameterCap size 5-1/8" long x 4-1/4" wide10-1/2" Tube length
C.E. Smith 53680Sa 80 Series Flush Mount Rod Holders, Swivel, 0 Degree - 53680Sa - 618-53680Saf1
White liner color316L Stainless steel1-7/8" Inner diameter Fits 2-1/2" hole diameterCap size 5-1/8" long x 4-1/4" wide10-1/2" Tube length
C.E. Smith 53681Ca 80 Series Flush Mount Rod Holders, Cast, 15 Degree - 53681Ca - 618-53681Caf1
White liner color316L Stainless steel1-7/8" Inner diameter Fits 2-1/2" hole diameterCap size 5-1/8" long x 4-1/4" wide10-1/2" Tube length
C.E. Smith 53681Sa 80 Series Flush Mount Rod Holders, Swivel, 15 Degree - 53681Sa - 618-53681Saf1
White liner color316L Stainless steel1-7/8" Inner diameter Fits 2-1/2" hole diameterCap size 5-1/8" long x 4-1/4" wide10-1/2" Tube length
C.E. Smith 53682Ca 80 Series Flush Mount Rod Holders, Cast, 30 Degree - 53682Ca - 618-53682Caf1
White liner color316L Stainless steel1-7/8" Inner diameter Fits 2-1/2" hole diameterCap size 5-1/8" long x 4-1/4" wide10-1/2" Tube length
C.E. Smith 53683A Backing Plate, 70 Series - 53683A - 618-53683Af1
Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. Regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Available for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Use your 1/4" stainless bolts and nuts (hardware not included).
C.E. Smith 53690A Drop-In Swivel - 53690A - 618-53690Af1
Instantly converts any in-gunnel rod holder to a swivel rod holder. Fits inside any rod holder with 1-9/16" or larger inside diameter. Investment cast 316L stainless construction. Smooth turning adjustable swivel resistance.
C.E. Smith 53770 Adjustable Aluminum Clamp-On Rod Holder, 7/8", 1" Or 1-1/16" Od - 53770 - 618-53770F1
Clear Anodized Finish100% Anodized marine grade aluminumPrecision machined for a slip resistant fitAngle adjusts in 30° incrementsIncludes 316L stainless steel screws
C.E. Smith 53771 Adjustable Aluminum Clamp-On Rod Holder, 1-1/4" Or 1-5/16" Od - 53771 - 618-53771F1
Clear Anodized Finish100% Anodized marine grade aluminumPrecision machined for a slip resistant fitAngle adjusts in 30° incrementsIncludes 316L stainless steel screws
C.E. Smith 53772 Adjustable Aluminum Clamp-On Rod Holder, 1-1/2" Or 1-21/32" Od - 53772 - 618-53772F1
Clear Anodized Finish100% Anodized marine grade aluminumPrecision machined for a slip resistant fitAngle adjusts in 30° incrementsIncludes 316L stainless steel screws
