Select Category
Brands
Weems & Plath Xxx Square Protractor - 2802 - 958-Wap002802F1
The Square Protractor is best suited for rapid plotting of course and bearing in a confined space. Sometimes referred to as a Douglas protractor, notations can be easily made directly on the matte plastic surface with a pencil.
Weems & Plath Xxx Star Finder 2102-D - 150 - 958-Wap000150F1
An invaluable tool for celestial navigators to locate and identify, by altitude and azimuth, the 57 stars listed in air and nautical almanacs. It can also be used by amateur star gazers for general star identification. The kit contains a durable black vinyl pouch with velcro closure that holds one star base and (10) 8-1/2" plastic templates.
Weems & Plath Xxx Weems Protractor - 255 - 958-Wap000255F1
Updated version of Breton & Portland Plotters Movable compass rose gridEdges graduated in inches & centimetersPencil & sharpener included
Weems Comfortmeter 5" Enduranc Pmg - 540900 - 958-540900F1
Weight Hook For 1-1/4" Booms - 1148 - 736-1148F1
Provides a hook on the downrigger boom for storage and transport of downrigger weights.
Weight Hooks - 1009 - 736-1009F1
Terminal Kit contains: 1 Swivel hook (No.1009), 3 sleeves, 1 stainless steel thimble and 1 soft stop bumper.
Weight Retreiver - 3025 - 736-3025F1
Great helper and safety precaution for the downrigger fisherman. Brings weights in for rigging lines and releases without having to lean out over the gunnel.
Weld Mount 008014 1:1 Plunger Only For At-300 Adhesive Dispensing Gun - At-14 - 817-008014F1
1:1 Plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10:1 plunger).
Weld Mount 008040 At-8040 No Slide Metal / Composite Bonder - At-8040 - 817-008040F1
Weld Mount AT-8040 is a solvent free, VOC Compliant, 2-part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. AT-8040 forms a tough, high strength bond usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.
Weld Mount 02010 At-2010 6 Minute Adhesive - At-2010 - 817-02010F1
A unique 1:1 adhesive. It has high viscosity and cures in 5 - 6 minutes with a 4 minute working or open time. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 12 month shelf life when stored at 72°F or less. Packaged In a 50 ml cartridge which will bond 150 - 200 parts. Dries brown.
Weld Mount 102424100 Stainless Steel Threaded Studs, 10-24 X 1-1/2", 100/Case - St125-1024-24Ss-100 - 817-102424100F1
Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate.
Weld Mount 142012100 Stainless Steel Threaded Studs, 1/4-20 X 3/4", 100/Case - St125-1420-12Ss-100 - 817-142012100F1
Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate.
Weld Mount 142016100 Stainless Steel Threaded Studs, 1/4-20 X 1", 100/Case - St125-1420-16Ss-100 - 817-142016100F1
Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate.
Weld Mount 142020100 Stainless Steel Threaded Studs, 1/4-20 X 1-1/4", 100/Case - St125-1420-20Ss-100 - 817-142020100F1
Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate.
Weld Mount 142032100 Stainless Steel Threaded Studs, 1/4-20 X 2", 100/Case - St-125-1420-32Ss-100 - 817-142032100F1
Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate.
Weld Mount 803001 At-300 Adhesive Dispensing Gun - At-300 - 817-803001F1
The AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10:1 plunger). Replacement plungers are also available. Dries gold.
Weld Mount 803900Bk At-3 Small Nylon Wire Tie Mount, Black, 100/Pack - At-3-100B - 817-803900Bkf1
For panel and other small space applications. Molded mount is sized for a 3/16" wide wire tie with a maximum width of .20". Average pull strength is about 50 lbs. and measures .44" square. Use for runs with only a few wires or in limited space. Excellent for mounting compass wires on center console boats and for overhead panel runs.
Weld Mount 803950 At-3 Small Nylon Wire Tie Mount, White, 50/Pack - At-3-50 - 817-803950F1
For panel and other small space applications. Molded mount is sized for a 3/16" wide wire tie with a maximum width of .20". Average pull strength is about 50 lbs. and measures .44" square. Use for runs with only a few wires or in limited space. Excellent for mounting compass wires on center console boats and for overhead panel runs.
Weld Mount 803950Bk At-3 Small Nylon Wire Tie Mount, Black, 50/Pack - At-3-50B - 817-803950Bkf1
For panel and other small space applications. Molded mount is sized for a 3/16" wide wire tie with a maximum width of .20". Average pull strength is about 50 lbs. and measures .44" square. Use for runs with only a few wires or in limited space. Excellent for mounting compass wires on center console boats and for overhead panel runs.
Weld Mount 805900Bk At-5 Large Nylon Wire Tie Mount, Black, 100/Pack - At-5B-100 - 817-805900Bkf1
Set into wet resin during the hull lay up or bonded with our acrylic adhesives. Designed for a 3/8" wide wire tie and has an average pull strength of 150 lbs. Approved for submerged bilge applications. No need for plywood in the hull just to have a place to drive wire tie screws. Saves material and labor costs!
Weld Mount 805950 At-5 Large Nylon Wire Tie Mount, White, 50/Pack - At-5-50 - 817-805950F1
Set into wet resin during the hull lay up or bonded with our acrylic adhesives. Designed for a 3/8" wide wire tie and has an average pull strength of 150 lbs. Approved for submerged bilge applications. No need for plywood in the hull just to have a place to drive wire tie screws. Saves material and labor costs!
Weld Mount 805950Bk At-5 Large Nylon Wire Tie Mount, Black, 50/Pack - At-5B-50 - 817-805950Bkf1
Set into wet resin during the hull lay up or bonded with our acrylic adhesives. Designed for a 3/8" wide wire tie and has an average pull strength of 150 lbs. Approved for submerged bilge applications. No need for plywood in the hull just to have a place to drive wire tie screws. Saves material and labor costs!
Weld Mount 807100 At- 7 Aluminum Base Wire Tie Mount, 100/Case - At-7-100 - 817-807100F1
An anodized aluminum base with a nylon tie mount riveted to the base. The nylon mount swivels 360°, making alignment with the wire harness easier. Designed for a #5 wire tie and has an average pull strength of 150 Lbs.
