Fultyme Rv
Plastic Wire Cover - 590-3084 - 590-3084F1
Gives vehicle that finished look. Covers unsightly wire pass-thru holes. Made of durable black plastic that will not corrode. Covers holes up to 1-1/4 in diameter.
Molded Line Connector - 590-3068 - 590-3068F1
Corrosion resistant construction. For 6, 12 and 24 volt applications. 7A @ 12V.
Manual Circuit Breaker50 Amp - 590-3041 - 590-3041F1
12/24V DC Type III manual resetPlastic body with molded mounting bracketsTwo 10/32 threaded studsPush to reset
Manual Circuit Breaker40 Amp - 590-3040 - 590-3040F1
12/24V DC Type III manual resetPlastic body with molded mounting bracketsTwo 10/32 threaded studsPush to reset
Manual Circuit Breaker30 Anp - 590-3039 - 590-3039F1
12/24V DC Type III manual resetPlastic body with molded mounting bracketsTwo 10/32 threaded studsPush to reset
Main Battery Switch - 590-3017 - 590-3017F1
Ignition protected. Use as main disconnect switch. Red plastic housing with large black plastic knob. For use with systems under 50V - 250A continuous / 360A intermittent.Made in the USA.
Locking Pin - 590-1036 - 590-1036F1
Keeps coupler release handle from disengaging while in travel. Will not prevent theft.
Led Sealed Identification Light Bar - 590-1165 - 590-1165F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed Sonically sealed, waterproofPolycarbonate lens and housingDesign includes both lead and ground wire
Led Sealed 3-Piece Identification Light Bar - - 590-1166F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed Designed for Over 80" Wide Trucks/TrailersWaterproof9 LED lightsSingle wireGrounds through mounting hardwareStainless steel base
Led Mini Sealed Marker/Clearance Light - - 590-1162F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed Sonically sealed, waterproofAccepts standard 1 or 2-wire plugsSingle wire design grounds through mounting hardwareBase and mounting hardware includedSingle diodePolycarbonate lens and housing
Led Mini Sealed Marker/Clearance Light - - 590-1161F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed Sonically sealed, waterproofAccepts standard 1 or 2-wire plugsSingle wire design grounds through mounting hardwareBase and mounting hardware includedSingle diodePolycarbonate lens and housing
Led Courtesy Interior Light - - 590-3004F1
12V. 4 LED lights. Pre-drilled to accommodate #6 screws. 3" Dia. x 5/8" D. Packed with both chrome and white bezels.
Led 6" Oval Sealed Tail Light Kit For Flush Mount - - 590-1159F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed Sonically sealed, waterproofKit includes light, grommet and plug3-Function: Red stop/turn/tail lightWith A70GB grommet and A47PB pigtail, PL-3 connection
Led 6" Oval Sealed Lights For Surface Mount - - 590-1160F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed. Mount in any 360 degree positionSonically sealed, waterproofFlange surface mount-no panel cut-out required3-function: Red stop/turn/tail light
In-Line Fuse Holder/Ato-Atc16 Gauge - 3036 - 590-3036F1
Water resistant. Easy to install, easy to change ATO-ATC fuse holder. Used in most recreational vehicles. Comes with cap to seal out moisture. Brass electrical contacts. Fuse included.
In-Line Fuse Holder/Ato-Atc12 Gauge - 590-3037 - 590-3037F1
Water resistant. Easy to install, easy to change ATO-ATC fuse holder. Used in most recreational vehicles. Comes with cap to seal out moisture. Brass electrical contacts. Fuse included.
Identification Light Bar - 590-1168 - 590-1168F1
Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed Surface mount on 7-1/2" centersSealed, waterproof lightsHard wired, power and groundPolycarbonate lens and housing, ABS base
Heavy Duty Drop Leg Trailer Jack 2500# Capacity - 1033 - 590-1033F1
Fixed mount jack with drop leg. Suited for heavy duty applications and fits trailer frames up to 3" x 5". Bolt-on style and includes all mountinghardware. 31" of lift.
Grease Cap - 590-1063 - 590-1063F1
Steel caps for most common application used in bearing kits.
Fuse Holder - 590-3024 - 590-3024F1
Panel mount. For 1/4" x 1 1/4" fuses. (fuses not included), with bayonet-type knob spring pressure contact. Complete with gasket and nut. For panels through 5/16".
