Select Category
Brands
Rod Holder Cap & Gasket Kit - 0480Dp0Blk - 9-0480Dp0Blkf1
Soft black flange gasket with integral flip-up cap and soft black lip. Use as replacement or as upgrade for older holders.
Rod Holder Cap & Gasket Kit - 0481Dp0Blk - 9-0481Dp0Blkf1
Soft black flange gasket with integral flip-up cap and soft black lip. Use as replacement or as upgrade for older holders.
Rod Holder Extension - 1138157 - 23-50163F1
Increase your odds with easier access to your rod and reel. Extends the height of the rod holder by 6", allowing for faster access when that fish strikes. Made from super tough glass filled nylon. Works with Attwood post mount rod holders.
Rod Holder Heavy Duty 0° Ss - Rh532Vs - 364-Rh532Vsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: heavy duty 4" x 5".
Rod Holder Heavy Duty 15° Ss - Rh534Hs - 364-Rh534Hsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: heavy duty 4" x 5".
Rod Holder Heavy Duty 30° Ss - Rh530Ss - 364-Rh530Ssf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: heavy duty 4" x 5".
Rod Holder Medium 0° Ss - Rh527Vs - 364-Rh527Vsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: medium 3-3/8" x 4-3/16".
Rod Holder Medium 15° - Rh529Hs - 364-Rh529Hsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: medium 3-3/8" x 4-3/16".
Rod Holder Medium 30° - Rh525Ss - 364-Rh525Ssf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: medium 3-3/8" x 4-3/16".
Rod Holder Mount Backing Plate - 441 - 736-441F1
Use the Scotty Backing Plate to add structural support when attaching the Scotty 241L / 241 Combination Side / Deck Mount or the Scotty 244L / 244 Flush Deck Mount to thin-walled watercraft. Made with super-tough reinforced nylon. Stainless steel nuts & machine screws included.
Rod Holder Swivel Base 0° - Rh577V - 364-Rh577Vf1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Swivel Base 15° - Rh579H - 364-Rh579Hf1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Swivel Base 30° - Rh575 - 364-Rh575F1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Swivel Base O° - Rh577Xl - 364-Rh577Xlf1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder-Flush-Black Nylon -Bul - 89270 - 50-89270F1
89211: Injection molded ABS flange with heavy walled PVC tube.89251/89271: Molded high impact plastic. Etched finish on flange. One-piece construction. Non-corrosive. Uses (3) fasteners #12 for installation.89221: Nylon reinforced with fiberglass. Stamped 304 stainless steel cover.89231: Nylon reinforced with fiberglass. Stamped 304 stainless steel cover. includes black rubber cap.
Rod Holder-Flush-White Nylon -Bul - 89250 - 50-89250F1
89211: Injection molded ABS flange with heavy walled PVC tube.89251/89271: Molded high impact plastic. Etched finish on flange. One-piece construction. Non-corrosive. Uses (3) fasteners #12 for installation.89221: Nylon reinforced with fiberglass. Stamped 304 stainless steel cover.89231: Nylon reinforced with fiberglass. Stamped 304 stainless steel cover. includes black rubber cap.
