Sea-Dog Line
Seadog Fillet Table Rod Holder Mount - 326515-3 - 354-3265153F1
Solid one-piece construction for long life and easy maintenanceEasily adjustable, multi-position gimbaled rod holder mounting system folds flat for easy storageUV stabilized high-density polypropylene constructionAssembles in minutes, all assembly hardware includedEasily accessible knife and pliers holdersHose holder and towel bar
Seadog Fillet Table Rod Holder Mount - 326510-3 - 354-3265103F1
Solid one-piece construction for long life and easy maintenanceEasily adjustable, multi-position gimbaled rod holder mounting system folds flat for easy storageUV stabilized high-density polypropylene constructionAssembles in minutes, all assembly hardware includedEasily accessible knife and pliers holders
Seadog Exhaust Thru Hull | Cast 316 Stainless | Includes Stainless Flap With Rubber Seal - 521130 - 354-521130F1
Stainless flap with rubber seal. Cast 316 Stainless.
Seadog Exhaust Thru Hull | Cast 316 Stainless | Includes Stainless Flap With Rubber Seal - 521125 - 354-521125F1
Stainless flap with rubber seal. Cast 316 Stainless.
Seadog Dual Round Voltmeter - 421616-1 - 354-4216161F1
This digital dual voltmeter displays voltage for main and auxiliary batteries simultaneously. The compact size allows installation in a wide variety of locations. Red LED display. IP65 rating. Injection molded nylon.
Seadog Drain Tube Flaring Tool - 520290-1 - 354-5202901F1
Drain Tube Flaring Tools for installing 1" drain tubes. Can be used to install all of Sea-Dog® Drain Tubes (520210-520430). Handy item for any toolbox. Drain tube not included.
Seadog Double Pole Double Throw 8 Terminal Blade Light Tip 12V 15 Amp Toggle Switch - 420128-1 - 354-4201281F1
Light Tip Toggle Switches are constructed of stamped brass and injection molded nylon with a polycarbonate toggle. Features a locking ring and lever seal to resist water penetration. Toggle bat features a lighted tip which is white in the OFF position and red in the ON position. Fits panels up to 1/4" thick and requires a 15/32" mounting hole. Easy installation. 15A @ 12VDC.
Seadog Deluxe Hand Held Rope Cutter - 300095-3 - 354-3000953F1
Easily cuts nylon, polyester, polypropylene and Dacron cordage and webbing Cuts and heat seals at the same timeReplaceable blade heats to 1100° Fahrenheit (600° Celsius) in less than 10 secondsBrass bristle cleaning brush, T-handle Allen wrench, and carrying case included10' heavy-duty grounded cordETL listed
Seadog Deck Step | Injection Molded Rubber & Stamped 304 Stainless - 328013-1 - 354-3280131F1
This Deck Step is lined with injection molded rubber to facilitate traction and framed by stamped 304 stainless steel for corrosion resistance and durability.
Seadog Combination Soft Bristle Brush & Squeegee - 491075-1 - 354-4910751F1
The Boat Hook Combination Soft Bristle Brush & Squeegee fits all Sea-Dog® Boat Hooks and universal/Acme threaded devices. This soft brush is constructed of injection molded nylon with a marine grade silicone rubber squeegee. Soft bristles are scratch resistant for gelcoat, paint, and plastic windows.
Seadog Clam Shell Vent | Stamped 304 Stainless | #6 Fastener - 331350-1 - 354-3313501F1
Clam shell ventilators provide splash protection for vent holes, wire or cable runs and blower-exhaust hose openings. 304 stamped stainless steel construction. Can be used for cabin ventilation with dorade boxes. Great for locker vents. Clam shell vents are ideal for applications where a taller vent would foul lines or restrict crew movement. Pre-drilled holes for a smooth screw on installation. #6 RH fasteners not included.
Seadog Clam Shell Vent | Stamped 304 Stainless | #6 Fastener - 331340-1 - 354-3313401F1
Clam shell ventilators provide splash protection for vent holes, wire or cable runs and blower-exhaust hose openings. 304 stamped stainless steel construction. Can be used for cabin ventilation with dorade boxes. Great for locker vents. Clam shell vents are ideal for applications where a taller vent would foul lines or restrict crew movement. Pre-drilled holes for a smooth screw on installation. #6 RH fasteners not included.
Seadog Clam Shell Vent | Stamped 304 Stainless | #6 Fastener - 331335-1 - 354-3313351F1
Clam shell ventilators provide splash protection for vent holes, wire or cable runs and blower-exhaust hose openings. 304 stamped stainless steel construction. Can be used for cabin ventilation with dorade boxes. Great for locker vents. Clam shell vents are ideal for applications where a taller vent would foul lines or restrict crew movement. Pre-drilled holes for a smooth screw on installation. #6 RH fasteners not included.
Seadog Chain Stopper Formed 304 Stainless Steel - 321825-1 - 354-3218251F1
Constructed of formed 304 stainless steel for strength and corrosion resistance, these Chain Stoppers help prevent damage to the windlass and reduce the risk of accidental free fall of the anchor while under way. Chain Stoppers mount alone or inside most bow rollers and work with your anchor roller to take tension off your windlass. Chain and rope should be secured at anchor when your windlass is not in use to avoid high loads the windlass was not designed for.Fits chain sizes 5/16"- 3/8".
Seadog Chain Stopper Formed 304 Stainless Steel - 321820-1 - 354-3218201F1
Constructed of formed 304 stainless steel for strength and corrosion resistance, these Chain Stoppers help prevent damage to the windlass and reduce the risk of accidental free fall of the anchor while under way. Chain Stoppers mount alone or inside most bow rollers and work with your anchor roller to take tension off your windlass. Chain and rope should be secured at anchor when your windlass is not in use to avoid high loads the windlass was not designed for.Fits chain sizes 3/16"- 1/4".
Seadog Cast Polished Brass Bell | #6 Fastener - 455721 - 354-455721F1
These Bells are constructed of improved cast brass (not lower grade spun brass). 8" Bells meets Coast Guard, ABYC, and NMMA requirements (200 cm mouth opening and striker mass no less than 3% of mass of the bell) for use on vessels 12m (39.4') to 20m (65.6') in length. Includes hanger and wall mounted bracket for easy installation. Installs with two #6 FH fasteners (not included). Chrome plated finish.
Seadog Cast Polished Brass Bell | #6 Fastener - 455720 - 354-455720F1
These Bells are constructed of improved cast brass (not lower grade spun brass). 8" Bells meets Coast Guard, ABYC, and NMMA requirements (200 cm mouth opening and striker mass no less than 3% of mass of the bell) for use on vessels 12m (39.4') to 20m (65.6') in length. Includes hanger and wall mounted bracket for easy installation. Installs with two #6 FH fasteners (not included). Mirror polished brass finish.
Seadog Cast Polished Brass Bell - #6 Fastener - 455001 - 354-455001F1
These Bells are constructed of improved cast brass (not lower grade spun brass). Meets Coast Guard, ABYC, and NMMA requirements (200 cm mouth opening and striker mass no less than 3% of mass of the bell) for use on vessels 12m (39.4") to 20m (65.6") in length. Includes hanger and wall mounted bracket for easy installation. Installs with two #6 FH fasteners (not included). Chrome plated finish.
Seadog Butt Hinge With Bearings | Commercial Pattern | Investment Cast 316 Stainless | 1/4" Fastener - 205246 - 354-205246F1
Constructed of investment cast 316 stainless steel these Butt Hinges are designed for applications where both extra strength and corrosion resistance are required. The integral nylon bearings promote rattle-free, silent movement and give the hinge a smoother action. The bearings also disburse the weight of the door compensating for heavier doors and increased use. Commercial ANSI templated screw hole pattern. Installs with eight 1/4" FH fasteners (not included).
Seadog Butt Hinge With Bearings | Commercial Pattern | Investment Cast 316 Stainless | 1/4" Fastener - 205244 - 354-205244F1
Constructed of investment cast 316 stainless steel these Butt Hinges are designed for applications where both extra strength and corrosion resistance are required. The integral nylon bearings promote rattle-free, silent movement and give the hinge a smoother action. The bearings also disburse the weight of the door compensating for heavier doors and increased use. Commercial ANSI templated screw hole pattern. Installs with eight 1/4" FH fasteners (not included).
Seadog Butt Hinge With Bearings | Commercial Pattern | Investment Cast 316 Stainless | 1/4" Fastener - 205243 - 354-205243F1
Constructed of investment cast 316 stainless steel these Butt Hinges are designed for applications where both extra strength and corrosion resistance are required. The integral nylon bearings promote rattle-free, silent movement and give the hinge a smoother action. The bearings also disburse the weight of the door compensating for heavier doors and increased use. Commercial ANSI templated screw hole pattern. Installs with eight 1/4" FH fasteners (not included).
Seadog Butt Hinge With Bearings | Commercial Pattern | Investment Cast 316 Stainless | 1/4" Fastener - 205242 - 354-205242F1
Constructed of investment cast 316 stainless steel these Butt Hinges are designed for applications where both extra strength and corrosion resistance are required. The integral nylon bearings promote rattle-free, silent movement and give the hinge a smoother action. The bearings also disburse the weight of the door compensating for heavier doors and increased use. Commercial ANSI templated screw hole pattern. Installs with eight 1/4" FH fasteners (not included).
Seadog Buss Bar Stud Terminal, 250A - 426738-1 - 354-4267381F1
These Buss Bar Stud Terminal Blocks are primarily used to route and connect power or ground circuits. The raised bus provides easy access on a single stud, making it useful for consolidating multiple wires or feeding multiple circuits. Constructed of tin plated brass and ABS. Maximum: 48VDC. Installs with #10 RH fasteners (not included).
Seadog Buss Bar Stud Terminal, 150A - 426728-1 - 354-4267281F1
These Buss Bar Stud Terminal Blocks are primarily used to route and connect power or ground circuits. The raised bus provides easy access on a single stud, making it useful for consolidating multiple wires or feeding multiple circuits. Constructed of tin plated brass and ABS. Maximum: 48VDC. Installs with #10 RH fasteners (not included).
Seadog Buss Bar Stud Terminal, 100A - 426718-1 - 354-4267181F1
These Buss Bar Stud Terminal Blocks are primarily used to route and connect power or ground circuits. The raised bus provides easy access on a single stud, making it useful for consolidating multiple wires or feeding multiple circuits. Constructed of tin plated brass and ABS. Maximum: 48VDC. Installs with #10 RH fasteners (not included).
