Taylor
Taylor Sur-Moor Shackle Buoy - White With Blue Reflective Striping - 46818 - 32-46818F1
The rope nest design has a built in cup shape at the top of the buoy that allows the anchor shackle to nest below the buoy surface. This recessed area helps shield the shackle from contacting the boat hull while making a convenient nesting place for the pennant line when the boat departs from the mooring. The hard-skin polyethylene shell is UV protected to resist the weathering effects of sunlight and is foam filled to positively displace water. Sandblasted finish. Tube Through-The-Center design with blue reflective striping. Shackle and hardware not included. T3C mooring collar recommended.
Taylor Sur-Mark Ii Marker Buoy 61" (Label Sold Separately) - 46103 - 32-46103F1
Made out of white polyethylene with closed cell foam inside. 37" shows above the water line. Accepts all Sur-Mark™ warning labels, not included.
Taylor Sur-Mark Buoy Label 13" X 24" Fits Sur-Mark Or Sur-Mark Ii (Sold In Pairs) - 46185 - 32-46185F1
Fade resistant and highly visible. Two labels required per buoy. Self adhesive.
Taylor Sur-Mark Buoy Label 13" X 24" Fits Sur-Mark Or Sur-Mark Ii (Sold In Pairs) - 46181 - 32-46181F1
Fade resistant and highly visible. Two labels required per buoy. Self adhesive.
Taylor Sur-Mark Buoy Label 13" X 24" Fits Sur-Mark Or Sur-Mark Ii (Sold In Pairs) - 46180 - 32-46180F1
Fade resistant and highly visible. Two labels required per buoy. Self adhesive.
Taylor Sully Stick Winter Stick - 22120 - 32-22120F1
Sully Stick™ winter stick - A long tapered buoy used in place of a standard round mooring buoy during the winter months. The Sully Stick has a molded in eyelet at the top for easy retrieval. The base eyelet is reinforced with a galvanized metal bushing to attach a rope and connect to the anchor chain. The shape of the Sully stick helps it escape ice entrapment better than a round buoy and can extend the useful life of a mooring buoy by protecting it from the damaging effects of freezing temperatures.
Taylor Stepsafe Single Tread Dock Step 22" L X 18" W X 11.5" H - White With Black Non-Slip Pad - 47100 - 32-47100F1
Molded in durable UV resistant polyethylene with non-slip pad on top of each step. 1-1/2" wide flange provides adequate mounting surface for docks. Hand rails are available for two and three step models, sold separately.
Taylor Stepsafe Non-Slip Pad 3-1/2" X 14-1/2" - Black - 11990 - 32-11990F1
Step with comfort and safety, wet or dry. Use on swim platforms, stair rungs, transoms or anywhere you step and could slip. Padded.
Taylor Standard Mooring Whips With Fixed 60° Angle Base (Sold In Pairs) For Boats Up To 29'-33' - Mw.160 - 32-Mw160F1
Mooring whips are a safe way to protect your boat against costly dockside and seawall damage. The Mooring Whip system pulls your boat a safe, convenient distance away from the dock thereby protecting it from the damaging forces of waves, wind, tides and wakes. Mooring Whips are made of high quality, solid fiberglass poles, aluminum- magnesium base units, tips, and mooring whip lines. Each set comes complete with all of the hardware necessary for installation.Standard mooring whips are equipped with fixed angle bases with a 60° angle, 13?16" diameter fiberglass poles and are most commonly used for ski boats, runabouts, center consoles, and bass boats in moderate wake areas. Sold in pairs.
Taylor Standard Mooring Whips With Fixed 60° Angle Base (Sold In Pairs) For Boats Up To 24'-28' - Mw.140 - 32-Mw140F1
Mooring whips are a safe way to protect your boat against costly dockside and seawall damage. The Mooring Whip system pulls your boat a safe, convenient distance away from the dock thereby protecting it from the damaging forces of waves, wind, tides and wakes. Mooring Whips are made of high quality, solid fiberglass poles, aluminum- magnesium base units, tips, and mooring whip lines. Each set comes complete with all of the hardware necessary for installation.Standard mooring whips are equipped with fixed angle bases with a 60° angle, 13?16" diameter fiberglass poles and are most commonly used for ski boats, runabouts, center consoles, and bass boats in moderate wake areas. Sold in pairs.
Taylor Standard Mooring Whips With Fixed 60° Angle Base (Sold In Pairs) For Boats Up To 20' - Mw.080 - 32-Mw080F1
Mooring whips are a safe way to protect your boat against costly dockside and seawall damage. The Mooring Whip system pulls your boat a safe, convenient distance away from the dock thereby protecting it from the damaging forces of waves, wind, tides and wakes. Mooring Whips are made of high quality, solid fiberglass poles, aluminum- magnesium base units, tips, and mooring whip lines. Each set comes complete with all of the hardware necessary for installation.Standard mooring whips are equipped with fixed angle bases with a 60° angle, 13?16" diameter fiberglass poles and are most commonly used for ski boats, runabouts, center consoles, and bass boats in moderate wake areas. Sold in pairs.
Taylor Standard Mooring Whips With Fixed 60° Angle Base (Sold In Pairs) For Boats Up To 18'-23' - Mw.120 - 32-Mw120F1
Mooring whips are a safe way to protect your boat against costly dockside and seawall damage. The Mooring Whip system pulls your boat a safe, convenient distance away from the dock thereby protecting it from the damaging forces of waves, wind, tides and wakes. Mooring Whips are made of high quality, solid fiberglass poles, aluminum- magnesium base units, tips, and mooring whip lines. Each set comes complete with all of the hardware necessary for installation.Standard mooring whips are equipped with fixed angle bases with a 60° angle, 13?16" diameter fiberglass poles and are most commonly used for ski boats, runabouts, center consoles, and bass boats in moderate wake areas. Sold in pairs.
Taylor Stainless Steel Top-Lok For Heavy 1" Round Trim (4 Per Pack) - 1348 - 32-1348F1
Has stud portion affixed. For heavy 1" round trim. Snaps on windshield frame.
Taylor Stainless Steel Top-Lok For Heavy 1" Round Trim (4 Per Pack) - 1344 - 32-1344F1
Has stud portion affixed. For heavy 1" round trim. Snaps on windshield frame.
Taylor Stainless Steel Top Mount Flag Pole Socket For 1-1/4" Poles, 10 Degree Angle - 966 - 32-966F1
Made from 316 polished stainless steel.
Taylor Stainless Steel Rail Mount Pulpit Staff 15" Long With Nylon Rail Clamp For 7/8" To 1-1/4" Rails - 971 - 32-971F1
Stainless steel. Complete with split rings and nylon rail clamp. Designed for round rails only.
Taylor Stainless Steel Rail Mount Flag Socket Fits 3/4" To 7/8" Poles And Mounts To 7/8" To 1-1/4" Rails - 968 - 32-968F1
Mounts to 7/8" to 1-1/4" round rails only. T304 Stainless Steel. Adjusts to any angle.
Taylor Stainless Steel Rail Mount Flag Pole Socket For 1" Diameter Flag Poles - 974 - 32-974F1
Stainless steel mounts will look great and provide years of service. Both models are perpendicular to the rail and are made for 1" diameter flag poles. Round rails only.
Taylor Stainless Steel Rail Mount Flag Pole Socket For 1" Diameter Flag Poles - 973 - 32-973F1
Stainless steel mounts will look great and provide years of service. Both models are perpendicular to the rail and are made for 1" diameter flag poles. Round rails only.
Taylor Stainless Steel Fender Rack - 3011 - 32-3011F1
A convenient place to stow fenders. Mounts on any rail and stanchion system. Movable J hooks mount on 1" - 1-1/8" rails and stanchion system, tightens to blend with any angle. Cross-reinforced for extra strength. Holds any style fender.Holds "Big B" and "Hull Gard" fenders effectively. Folds flat for easy storage.
Taylor Stainless Steel Fender Rack - 2011 - 32-2011F1
A convenient place to stow fenders. Mounts on any rail and stanchion system. Movable J hooks mount on 1" - 1-1/8" rails and stanchion system, tightens to blend with any angle. Cross-reinforced for extra strength. Holds any style fender.Holds "Big B" and "Hull Gard" fenders effectively. Folds flat for easy storage.
Taylor Stainless Steel Fender Rack - 2009 - 32-2009F1
A convenient place to stow fenders. Mounts on any rail and stanchion system. Movable J hooks mount on 1" - 1-1/8" rails and stanchion system, tightens to blend with any angle. Cross-reinforced for extra strength. Holds any style fender.Holds "Big B" and "Hull Gard" fenders effectively. Folds flat for easy storage.
Taylor Stainless Steel Fender Lock For Rope Up To 1/2" - 1001 - 32-1001F1
Taylor Made has designed a larger version of it's best selling 1010 fender adjuster. Stainless steel construction, adjustment peg, and fastening screws insure many years of dependable service in the harsh marine environment. The "one-way" locking peg provides secure and reliable mounting and allows the use of up to 1/2" diameter rope.
Taylor Stainless Steel Dog Snap (2 Per Pack) - 1340 - 32-1340F1
1" stainless steel snap.
Taylor Stainless Steel Clinching Rings (Pack Of 50) - 1045 - 32-1045F1
Taylor Stainless Steel Clinching Rings. Fits 3/8"-1/2" cord. (Pack of 50)
