Weaver Industries (Canada Only)
Weaver Pin&Lanyard Replacement Pin & Lanyard - Quick-Pin - 957-Pin&Lanyardf1
Replacement Pin & Lanyard
Weaver Mst Motosto Transom Mount Motor Bracket - Motosto-Tr - 957-Mstf1
Allows you to store your 15 hp or smaller on the transom of your yacht. When under way the bracket is in normal position and when using the motor the bracket can be swung out of the way against the transom. This bracket is not removable.
Weaver Mss Motosto Swim Platform Motor Bracket - Motosto-Sw - 957-Mssf1
Allows you to remove your motor from your dinghy and place it on the swim platform in a horizontal position before getting out of your dinghy. The bracket is removable from the swim step leaving a low profile receiver plate on the swim platform similar to the Weaver Quick Kit bracket. Dimensions 13" W x 5" D x 10" H.
Weaver Motokr8 Weaver Moto Kicker Swim Platform Motor Bracket - Moto-Kr8 - 957-Motokr8F1
This trolling motor fixed bracket is designed to install on a swim platform. It will hold up to a 9.9 hp 4 stroke engine. Made for the marine enviroment from 304 s/s with welded seams. The mounting pad is made from Starboard. Bracket dimensions 11.25"W x 5"D (+1.5" Pad) x 8"H.
Weaver Leaverstds Standard Weaver Leaver, Starboard Side - Leaver-S - 957-Leaverstdsf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Standard: For transoms up to 4" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Leaverstdp Standard Weaver Leaver, Port Side - Leaver-P - 957-Leaverstdpf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Standard: For transoms up to 4" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Leaverm3S Model 3 Weaver Leaver, Starboard Side - Lvr-M3-S - 957-Leaverm3Sf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Model 3: For deep transoms up to 6" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Leaverm3P Model 3 Weaver Leaver, Port Side - Lvr-M3-P - 957-Leaverm3Pf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Model 3: For deep transoms up to 6" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Lclip L Brackets For Standoffs, 4-Pack - Lclip - 957-Lclipf1
L Brackets for Standoffs, 4-Pack
Weaver Hoistleaver Hoist/Leaver - Hoist Delux - 957-Hoistleaverf1
Pick up your dinghy and motor at the same time using our foot operated hoist. Lifting from the Leaver bracket that your dinghy motor is attached to, the dinghy raises at the same time as the motor is swinging out over the swim platform. After the dinghy and motor are brought into the vertical position, the hoist remains hooked up to the dinghy/motor. For hard bottom dinghies. You will need to order the HDRBD202 davit system (not included) and at least one stand-off bracket at the bow of the inflatable for more stabilization. HD-RBD202 required for hoist/leaver installation, sold separately.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Hdrbd202 Heady Duty Davit System For Inflatables - Hd-Rbd201 - 957-Hdrbd202F1
This complete davit hook up allows you to attach a 10' to 12' inflatable dinghy to the swim platform. Only for hard bottom dinghies. It includes the HD-Front Arc, 2 HD-RS110 davit heads w/Quick Kits, and the Transom Arc (select the Transom Arc that you need for your dinghy). This will need to go with the Weaver Hoist/Leaver and will take weights up to 400 lbs..
Weaver Dhs Davit Head For 7'-9' Hard-Shelled Dinghies - Dhs - 957-Dhsf1
The Dinghy side of the Weaver Davit Systems for fiberglass dinghies.
Weaver Csbolt4 4" Spacer Bolts For Chocks - 4-Boltext - 957-Csbolt4F1
Designed to retrofit pads to a different height. Spacer Bolts to raise the pads up on the C1204, C1207 and C1208 chocks.
Weaver Csbolt3 3" Spacer Bolts For Chocks - 3-Boltext - 957-Csbolt3F1
Designed to retrofit pads to a different height. Spacer Bolts to raise the pads up on the C1204, C1207 and C1208 chocks.
Weaver Csbolt2 2" Spacer Bolts For Chocks - 2-Boltext - 957-Csbolt2F1
Designed to retrofit pads to a different height. Spacer Bolts to raise the pads up on the C1204, C1207 and C1208 chocks.
Weaver Csbolt1 1" Spacer Bolts For Chocks - 1-Boltext - 957-Csbolt1F1
Designed to retrofit pads to a different height. Spacer Bolts to raise the pads up on the C1204, C1207 and C1208 chocks.
Weaver Csbolt Standard Spacer Bolts For Chocks - Csbolt - 957-Csboltf1
Designed to retrofit pads to a different height. Spacer Bolts to raise the pads up on the C1204, C1207 and C1208 chocks.
Weaver C1208Rem Swivel (Removable) Dinghy Chocks, 4/Pk - C1208Crem - 957-C1208Remf1
Universal chocks for mounting a hard bottomed dinghy on the deck or bridge of a yacht. Swivel: Pads swivel in any direction and can be adjusted up by using spacer bolts (sold separately). Removable: Includes Removable bases that let you remove the stanchions from your deck or bridge if you have an area you use for other purposes.
Weaver C1207Rem Swivel (Removable) Dinghy Chocks, 4/Pk - C1207Crem - 957-C1207Remf1
Universal chocks for mounting a hard bottomed dinghy on the deck or bridge of a yacht. Swivel: Pads swivel in any direction and can be adjusted up by using spacer bolts (sold separately). Removable: Includes Removable bases that let you remove the stanchions from your deck or bridge if you have an area you use for other purposes.
Weaver C1204Rem Swivel (Removable) Dinghy Chocks, 4/Pk - C1204Crem - 957-C1204Remf1
Universal chocks for mounting a hard bottomed dinghy on the deck or bridge of a yacht. Swivel: Pads swivel in any direction and can be adjusted up by using spacer bolts (sold separately). Removable: Includes Removable bases that let you remove the stanchions from your deck or bridge if you have an area you use for other purposes.
Weaver C1000Rem Standard Dinghy Chocks, 4/Pk - C1000Crem - 957-C1000Remf1
Universal chocks for mounting a hard bottomed dinghy on the deck or bridge of a yacht. Standard: Pads go back and forth in one direction.
Weaver Arct2 Transom Arc Davits For Inflatables, 18" Tubes - Arc2 - 957-Arct2F1
The Arc transfers the weight of heavier outboards from the transom of the inflatable to the swim platform. The stainless steel Arc is built to be removed when not in use. The Arc snaps easily into the davit head on the swim platform. Includes a special receiver bracket that mounts on the inflatable transom. It's simple receiver release pin allows for easy removal and storage.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Arct1 Transom Arc Davits For Inflatables, 16"-17" Tubes - Arc1 - 957-Arct1F1
The Arc transfers the weight of heavier outboards from the transom of the inflatable to the swim platform. The stainless steel Arc is built to be removed when not in use. The Arc snaps easily into the davit head on the swim platform. Includes a special receiver bracket that mounts on the inflatable transom. It's simple receiver release pin allows for easy removal and storage.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Arcf Front Arc - Frontarc - 957-Arcff1
A fully adjustable 3-point mounting pad unit that glues to the fiberglass floor of inflatable dinghies. The unique design allows for a wide variety of adjustment points for most modern inflatables. A valuable companion to the Weaver Arc that is mounted on the transom. Together, the Weaver Arc and the Weaver Front Arc are highly effective in transferring the weight of inflatables to the Weaver Snap Davits.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver 957-Rbd100Garct2 Transom Arc Davits For Inflatables, 18" Tubes - Rbd100G-Arc2 - 957-Rbd100Garct2F1
The Arc transfers the weight of heavier outboards from the transom of the inflatable to the swim platform. The stainless steel Arc is built to be removed when not in use. The Arc snaps easily into the davit head on the swim platform. Includes a special receiver bracket that mounts on the inflatable transom. It's simple receiver release pin allows for easy removal and storage.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
