Select Category
_0x200.jpg)
Weaver Hoistleaver Hoist/Leaver - Hoist Delux - 957-Hoistleaverf1
Pick up your dinghy and motor at the same time using our foot operated hoist. Lifting from the Leaver bracket that your dinghy motor is attached to, the dinghy raises at the same time as the motor is swinging out over the swim platform. After the dinghy and motor are brought into the vertical position, the hoist remains hooked up to the dinghy/motor. For hard bottom dinghies. You will need to order the HDRBD202 davit system (not included) and at least one stand-off bracket at the bow of the inflatable for more stabilization. HD-RBD202 required for hoist/leaver installation, sold separately.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Lclip L Brackets For Standoffs, 4-Pack - Lclip - 957-Lclipf1
L Brackets for Standoffs, 4-Pack
Weaver Leaverm3P Model 3 Weaver Leaver, Port Side - Lvr-M3-P - 957-Leaverm3Pf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Model 3: For deep transoms up to 6" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Leaverm3S Model 3 Weaver Leaver, Starboard Side - Lvr-M3-S - 957-Leaverm3Sf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Model 3: For deep transoms up to 6" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Leaverstdp Standard Weaver Leaver, Port Side - Leaver-P - 957-Leaverstdpf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Standard: For transoms up to 4" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Leaverstds Standard Weaver Leaver, Starboard Side - Leaver-S - 957-Leaverstdsf1
Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Standard: For transoms up to 4" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Motokr8 Weaver Moto Kicker Swim Platform Motor Bracket - Moto-Kr8 - 957-Motokr8F1
This trolling motor fixed bracket is designed to install on a swim platform. It will hold up to a 9.9 hp 4 stroke engine. Made for the marine enviroment from 304 s/s with welded seams. The mounting pad is made from Starboard. Bracket dimensions 11.25"W x 5"D (+1.5" Pad) x 8"H.
Weaver Mss Motosto Swim Platform Motor Bracket - Motosto-Sw - 957-Mssf1
Allows you to remove your motor from your dinghy and place it on the swim platform in a horizontal position before getting out of your dinghy. The bracket is removable from the swim step leaving a low profile receiver plate on the swim platform similar to the Weaver Quick Kit bracket. Dimensions 13" W x 5" D x 10" H.
Weaver Mst Motosto Transom Mount Motor Bracket - Motosto-Tr - 957-Mstf1
Allows you to store your 15 hp or smaller on the transom of your yacht. When under way the bracket is in normal position and when using the motor the bracket can be swung out of the way against the transom. This bracket is not removable.
Weaver Pin&Lanyard Replacement Pin & Lanyard - Quick-Pin - 957-Pin&Lanyardf1
Replacement Pin & Lanyard
Weaver Pinl Large Push Pin - Long-Pin - 957-Pinlf1
Large Push Pin
Weaver Pins Small Push Pin - Short-Pin - 957-Pinsf1
Small Push Pin
Weaver Quick Kit, 2/Pk - Quickkit - 957-Quickf1
Receiver plates for easy removal of the Davit Heads from the swim platform for use with the RBD100 and SSHR for the SD1. Comes with all the mounting hardware plus the pin and lanyard. Not to be used with RS150.
Weaver Quickw Quick Removal Kit For Weaver Winch - Qrk - 957-Quickwf1
Quick Removal Kit for Weaver Winch
Weaver Rbd100 Swim Grid Snap Davits For Inflatables, Black - Rbd100 - 957-Rbd100F1
Designed for inflatable boats with a total weight of 150 lbs or less. 100% solid stainless steel, all hardware included. Push release and snap hook-up prevents pinched fingers. Provides safe entry to and exit from inflatable dinghy. Hypalon, molded rubber parts, resistant to sun and salt.
Weaver Rbd100G Swim Grid Snap Davits For Inflatables, Grey - Rbd100G - 957-Rbd100Gf1
Designed for inflatable boats with a total weight of 150 lbs or less. 100% solid stainless steel, all hardware included. Push release and snap hook-up prevents pinched fingers. Provides safe entry to and exit from inflatable dinghy. Hypalon, molded rubber parts, resistant to sun and salt.
Weaver Rbd100Garct1 Transom Arc Davits For Inflatables, 16"-17" Tubes - Rbd100G-Arc1 - 957-Rbd100Garct1F1
The Arc transfers the weight of heavier outboards from the transom of the inflatable to the swim platform. The stainless steel Arc is built to be removed when not in use. The Arc snaps easily into the davit head on the swim platform. Includes a special receiver bracket that mounts on the inflatable transom. It's simple receiver release pin allows for easy removal and storage.Weaver worksheet must be filled out as this product is custom tailored.Visit weaverindustries.com for Additional Info & Measurement Instructions
Weaver Rbd150G Transom Snap Davits For Inflatables, Grey - Rbd150G - 957-Rbd150Gf1
Designed for inflatable boats with a total weight of 150 lbs or less. 100% solid stainless steel, all hardware included. Push release and snap hook-up prevents pinched fingers. Provides safe entry to and exit from inflatable dinghy. Hypalon, molded rubber parts, resistant to sun and salt.
Weaver Rp101 Spare Pad For Rbd100 & Rbd150, Black - Rp101 - 957-Rp101F1
Spare Pad for RBD100 & RBD150.
Weaver Rp101G Spare Pad For Rbd100 & Rbd150, Grey - Rp101-Grey - 957-Rp101Gf1
Spare Pad for RBD100 & RBD150.
Weaver Rp301 Stand-Off Pad, Black - Rp301 - 957-Rp301F1
This hypalon, molded rubber pad is used to clip stand-offs to inflatable boats.
Weaver Rp301G Stand-Off Pad, Grey - Rp301-Grey - 957-Rp301Gf1
This hypalon, molded rubber pad is used to clip stand-offs to inflatable boats.
Weaver Rp304G Stand-Off Pad, Grey With Swivel - Rp304 - 957-Rp304Gf1
This hypalon, molded rubber pad is used to clip stand-offs to inflatable boats.
Weaver Rs110 Standard Davit Head - Rs110 - 957-Rs110F1
For RBD100. Sold by the each.
Weaver Rs1102X2 Offset Davit Head - Offset2X2 - 957-Rs1102X2F1
For RBD100. Sold by the each.
