Select Category
Electrical
Isolator Bolts, 4-Pack - 69060 - 452-69060F1
Easily install your anchor winch, trolling motor and other accessories from the top of your boat deck - great when you can't reach under the deck! Protects your boat from vibrations. Marine-grade 316 stainless steel bolts are easily installed in a 1/2" hole with Phillips head screwdriver. For accessory frames up to 1-1/8" thick.
Iota Dls-75 75 Amp Power Converter Battery Charger - Dls-75 - 683-Dls75F1
The DLS-75 Power Converter/Battery Charger from IOTA Engineering converts nominal 108-132 AC voltage to 13.4 DC voltage for both DC load operation and 12V battery charging. As a power supply, the unit's tightly controlled regulation allows the user to operate a nominal 12VDC load up to 75 amps. As a battery charger, the unit will maintain the battery, delivering its full-rated current when the battery capacity falls sufficiently low. The voltage is set to deliver its maximum current for the necessary period of time to minimize undue stress to the battery caused by heating of its cells. This helps to ensure the longest possible life of the battery. Over time, as the battery nears its full capacity, the DLS-75 will automatically drop the current, providing a float-charge to the battery to prevent self-discharge of the cells. INPUT VOLTAGE: 108-132 VACINPUT FREQUENCY: 50-60 HzOUTPUT VOLTAGE: 13.4 VDCOUTPUT AMPERAGE: 75 Amps
Iota Dls-55 55 Amp Power Converter Battery Charger - Dls-55 - 683-Dls55F1
The DLS-55 Power Converter/Battery Charger from IOTA Engineering converts nominal 108-132 AC voltage to 13.4 DC voltage for both DC load operation and 12V battery charging. As a power supply, the unit's tightly controlled regulation allows the user to operate a nominal 12VDC load up to 55 amps. As a battery charger, the unit will maintain the battery, delivering its full-rated current when the battery capacity falls sufficiently low. The voltage is set to deliver its maximum current for the necessary period of time to minimize undue stress to the battery caused by heating of its cells. This helps to ensure the longest possible life of the battery. Over time, as the battery nears its full capacity, the DLS-55 will automatically drop the current, providing a float-charge to the battery to prevent self-discharge of the cells. INPUT VOLTAGE: 108-132 VACINPUT FREQUENCY: 50-60 HzOUTPUT VOLTAGE: 13.4 VDCOUTPUT AMPERAGE: 55 Amps
Iota Dls-45 45 Amp Power Converter Battery Charger - Dls-45 - 683-Dls45F1
The DLS-45 Power Converter/Battery Charger from IOTA Engineering converts nominal 108-132 AC voltage to 13.4 DC voltage for both DC load operation and 12V battery charging. As a power supply, the unit's tightly controlled regulation allows the user to operate a nominal 12VDC load up to 45 amps. As a battery charger, the unit will maintain the battery, delivering its full-rated current when the battery capacity falls sufficiently low. The voltage is set to deliver its maximum current for the necessary period of time to minimize undue stress to the battery caused by heating of its cells. This helps to ensure the longest possible life of the battery. Over time, as the battery nears its full capacity, the DLS-45 will automatically drop the current, providing a float-charge to the battery to prevent self-discharge of the cells. INPUT VOLTAGE: 108-132 VACINPUT FREQUENCY: 50-60 HzOUTPUT VOLTAGE: 13.4 VDCOUTPUT AMPERAGE: 45 Amps
Inverter Chrg 3000W 150A - Wf-7230 - 715-Wf7230F1
Interlux Yaa8692G Interfill 830 Lightweight Epoxy Fairing Compound, Part B Fast Cure2 Gal. - Yaa869/2 - 94-Yaa8692Gf1
Interfill 830 Fast Cure is the best choice for profiling above and below the waterline on Steel, Aluminium and Composite hulls. The special two-component light grey epoxy formulation can fill up to a thickness of 800 mils in one coat without the risk of sagging/slumping. Fast curing at lower temperatures and low density compositionHigh-strength and impact resistance, waterproof and easy to sandWhen sanded, the surface is smooth enough to be directly overcoated
Interlux Yaa8672G Interfill 830 Lightweight Epoxy Fairing Compound, Part A Base, Gal. - Yaa867/2 - 94-Yaa8672Gf1
A special 2-component, light grey, epoxy that fills gaps of up to 800 mils without sagging. This makes it perfect for profiling above and below the waterline on steel, aluminum and composite hulls. A waterproof, high strength and impact resistant epoxyFills gaps of up to an inch with saggingEasy to sand and fast curing times at lower temperatures
Intellisteer Type T Wireless For Mech Steering W/Tilt - Inttypet - 491-Inttypetf1
Intellisteer Type S Wireless For Mech Steering W/O Tilt - Inttypes - 491-Inttypesf1
Intellisteer Type H Wireless For Hydraulic Steering - Inttypeh - 491-Inttypehf1
Intellisteer Type A Wireless Steering - Inttypea - 491-Inttypeaf1
Control Unit for Existing Drives or Autopilot. No need for additional drive units. The Intellisteer Wireless Controller is designed to be wired between a Course Computer and Autopilot DriveWhen the Intellisteer Wireless Controller is activated it will disconnect the autopilot and provide wireless jog steering control from anywhere on the boatWhen the Intellisteer Wireless Controller is turned off, the Autopilot will function as beforeEasy DIY installation, no professional installer needed2 year limited warranty, purchase with confidence Includes: Wireless Control (meets FCC standards, auto shut-off, waterproof, over 1M control codes), Receiver Module, Easy to use installation kit.
Insta Trim 12735 25' Wire Harness - 12735 - 754-12735F1
25' Wire Harness
Insta Trim 12701 12V Soleniod Valve W/White Wire - 12701 - 754-12701F1
12V Soleniod Valve w/White Wire
Insta Trim 12657B Outside Housing W/O Female Wire Receptacle - 12657-B - 754-12657Bf1
Outside Housing w/o Female Wire Receptacle
Inr Mbr Dx8.5L Drm No Solenoid Ufp - 099-184-00 - 641-9918400F1
Inline Fuse Holder (Waterproof - 420555-1 - 354-4205551F1
AGC Watertight Inline Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4" x 1-1/4" glass fuse.
Inline Fuse Holder (Waterproof - 420554-1 - 354-4205541F1
AGC Watertight Inline Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4" x 1-1/4" glass fuse.
Inline Fuse Holder (Waterproof - 420553-1 - 354-4205531F1
AGC Watertight Inline Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4" x 1-1/4" glass fuse.
Inline Fuse Holder (Waterproof - 420552-1 - 354-4205521F1
AGC Watertight Inline Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4" x 1-1/4" glass fuse.
Inline Fuse Holder - 445199-1 - 354-4451991F1
ATO/ATC Inline Fuse Holder is constructed of injection molded, fiberglass reinforced nylon. Designed to accept ATO/ATC automotive-style spade terminal fuses. Maximum: 30A. 14 gauge 4" AWG wire lead. Fuse not included. Use with fuses (445101-445130).
Inline Fuse - 420500-1 - 354-4205001F1
AGC Inline Fuse Holder is constructed with Injection molded nylon. Overcurrent protection in a convenient push together inline holder. To install, cut a 11-1/2" wire lead from 14 gauge wire and strip both ends. For use with standard AGC 1/4" x 1-1/4" glass style fuses. Maximum 20A @ 12VDC. 20A AGC fuse included.
Inline 50 Amp Fuse Holder - 420557-1 - 354-4205571F1
AGC Watertight Inline Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4" x 1-1/4" glass fuse.
Inline 30 Amp Fuse Holder - 420565-1 - 354-4205651F1
ACG Watertight Inline Dual Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4" x 1-1/4" glass fuse and an extra emergency fuse. Fuse holder has a specially designed case that is molded with a second fuse pocket for convenient access to a spare fuse.
