Select Category
Electronics & Instruments
Transducer Paint - Mdr-720 - 79-Mdr720F1
A waterbased antifouling paint designed specifically to inhibit barnacles and marine growth on depth sounder transducers in fresh and salt water. Brush-in-cap container and water clean up make this product easy to use. Twelve 2 oz. containers per counter display.
Transducer Mounting Board - 900 - 750-900F1
Holds 1 to 2 transducers or paddle wheels. Helps to eliminate drilling permanent holes below the water line to prevent leakageMakes it easy to install, move or adjust your transducer to get the maximum benefit from your fish locatorHigh-density polyethylene plate will not warp, corrode, or be affected by sunlight.Comes with stainless mounting hardwareBottom of plate can be easily cut to any hull angle
Tireminder Pressure Sensors, 2/Pk - Tm22115Vp - 777-Tm22115Vpf1
Senses tire pressure and transmits signal to the display unit. Compatible with all TireMinder Tire Pressure Monitoring SystemsTPMS for RV, Trailer, MotorHome, Truck, Car or Any Other Vehicle with Brass (Rubber) or Steel Valve StemsReplaceable Battery with 9-14 Month Lifespan (CR1632)Simply Replaces Valve Cap; Small, Light, and Out of the Way (0.5 OZ)
Temperature Sender - 50-15341 - 50-15341F1
Ground: Standard Connection: .250" SpadeWorks with Seachoice gauges
Taylor Charlevoix Burgee And Antenna Clips 1/2" - 57925 - 32-57925F1
Are designed to allow you to fly your burgee or courtesy flag from your antenna without fear of losing it. Fit standard 1/2" burgee poles or 1/2" whip antennas. Neoprene is provided for use on poles or antennas smaller than 1/2".
Taco Gs860 Grand Slam 860 Electric Vhf Antenna Mount - Gs-860 - 236-Gs860F1
Polished stainless-steel body with a mirrored finishSmooth lift and descentStandard 1"-14 thread (male) shaft accommodates standard VHF antennas up to 8'No under-mount clearance neededHigh-torque, anti-backlash ball-bearing motorIntegrated nylon knob on breakaway pin allows for manual operation in case of power failureElectronic Control Module includes a 5A fuse for device protectionComes with a 12" wire lead and water-sealed Deutsch connector, using 18-gauge wire from the baseOperates on 12-volt DC for lift and descent1-year limited warranty
Taco Gs850 Grand Slam Electric Vhf Antenna Mount - Gs-850 - 236-Gs850F1
Designed with safety and innovation in mind, boaters can adjust the position of their antenna with the simple push of a button from the comfort of their helm. The GS-850 is a fully electric unit with hidden wires inside the hardtop. This mount easily installs to the surface of the hardtop and fits all top thicknesses. Standard 1"-14 thread (male) shaft to accept standard antennas up to 8'No under-mount clearance requiredMachined / Anodized aluminum body with a light brushed finishThreaded shaft for consistent lift and descentDelrin bearings for smooth operationFeatures breakaway pin for manual adjustmentKit includes drill template and installation instructionsIncludes 6" lead for 12-volt DC power supply for lift and descentAccepts 7A fuse in the main +12 VDC power feed (not included)
Taco Gs8001 Grand Slam Universal Antenna Mount - Gs-800-1 - 236-Gs8001F1
The GS-800 VHF Antenna Mount was created specifically to prevent climbing on the boat gunnel to raise and lower a VHF antenna. Lift and descend the antenna from the safety of the deck from under the top. Its smooth operation, attractive machined aluminum frame and cast stainless-steel rotator make this item a must for any boater. Safe, no-hassle raising and lowering of a VHF antennaNo more climbing on T-tops or gunnelsStandard 1"-14 thread (male) shaft to accept standard VHF antennasMachined / Anodized aluminum bodyLight brushed finishPolished Type-316L stainless steel crank handleFolding crank handle locks flush into baseThreaded shaft for consistent lift and descentDelrin bearings for smooth operationRoller bearings in crank assemblyMounts through up to 2" thick hardtopsIncludes 4" x 1/4" round backing plate (hardware not included)Made in the USA1-year limited warranty
T-H Marine Atlas Series Digital Position Gauge Kit - Fagk2Ssdp - 232-Fagk2Ssdpf1
Digital LED position gauges fit Atlas hydraulic jack plates. Numbers range from 0-20 and each number indicates a 1/4" rise. Atlas jack plates are predrilled to accept sensors.
T-H Marine Atlas Series Digital Position Gauge Kit - Fagk2Dp - 232-Fagk2Dpf1
Digital LED position gauges fit Atlas hydraulic jack plates. Numbers range from 0-20 and each number indicates a 1/4" rise. Atlas jack plates are predrilled to accept sensors.
T-H Marine Atlas Series Digital Position Gauge Kit - Fagk1Ssdp - 232-Fagk1Ssdpf1
Digital LED position gauges fit Atlas hydraulic jack plates. Numbers range from 0-20 and each number indicates a 1/4" rise. Atlas jack plates are predrilled to accept sensors.
Sugatsune P6107 Seamaster Pro Range Am/Fm Antenna - P6107 - 944-P6107F1
Pro Series Antennas can be removed and remounted on the boat at the user's convenience. The cable is hardwired to the Pro Series mount, so the antenna can be removed without pulling or cutting the cable. SeaMaster Pro Series antennas are an excellent choice for new installations on small to medium sized boats. Robust, reliable and good looking, they will provide outstanding performance for years. SeaMaster Pro Series antennas must be used with SeaMaster Pro Series Mounts, which give the options of side, deck or rail mounting your antenna. AM/FM 0.45m heliflex antenna. Designed for boat owners who do not go far offshore, but would like an improvement in their AM/FM reception.
Submersible Speaker Mic - Cmp460 - 783-Cmp460F1
Standard Horizon CMP460 submersible noise canceling speaker mic for VHF handheld model HX370, HX400, HX471, HX500, HX600, HX751, HX851, HX750S and HX850S.
