Select Category
General
Rod Holder Swivel Base O° - Rh577Xl - 364-Rh577Xlf1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Swivel Base 30° - Rh575 - 364-Rh575F1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Swivel Base 15° - Rh579H - 364-Rh579Hf1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Swivel Base 0° - Rh577V - 364-Rh577Vf1
Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch brass lock nut at the bottom of the rod holder.
Rod Holder Mount Backing Plate - 441 - 736-441F1
Use the Scotty Backing Plate to add structural support when attaching the Scotty 241L / 241 Combination Side / Deck Mount or the Scotty 244L / 244 Flush Deck Mount to thin-walled watercraft. Made with super-tough reinforced nylon. Stainless steel nuts & machine screws included.
Rod Holder Medium 30° - Rh525Ss - 364-Rh525Ssf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: medium 3-3/8" x 4-3/16".
Rod Holder Medium 15° - Rh529Hs - 364-Rh529Hsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: medium 3-3/8" x 4-3/16".
Rod Holder Medium 0° Ss - Rh527Vs - 364-Rh527Vsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: medium 3-3/8" x 4-3/16".
Rod Holder Heavy Duty 30° Ss - Rh530Ss - 364-Rh530Ssf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: heavy duty 4" x 5".
Rod Holder Heavy Duty 15° Ss - Rh534Hs - 364-Rh534Hsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: heavy duty 4" x 5".
Rod Holder Heavy Duty 0° Ss - Rh532Vs - 364-Rh532Vsf1
Stainless steel rod holders are drilled and countersunk for 1/4" bolts. It is highly recommended that these units be "through-bolted", and not attached with screws, when possible. Top (plate) measurements: heavy duty 4" x 5".
Rod Holder Extension - 1138157 - 23-50163F1
Increase your odds with easier access to your rod and reel. Extends the height of the rod holder by 6", allowing for faster access when that fish strikes. Made from super tough glass filled nylon. Works with Attwood post mount rod holders.
Rod End - Gs62890 - 11-Gs62890F1
Rod end with internal threads for either end of Nautalift gas filled lift supports.
Rod Boss Trec Tack End Caps, Set Of 2 - Trec - 767-Trecf1
Keep your rod holders and equipment safe with the Rod Boss™ track end caps. Rod Boss™ track end caps are machined out of aluminum and have a clear anodized finish to protect the product from harsh environmental conditions on the water. Installing the Rod Boss™ Track End Caps is as easy as sliding them into the ends of your track, aligning the mounting holes with the track holes, and tightening the flat head cap screws down. Universal to all standard 3" track.Comes with two M6 x 1.0 stainless steel flat head cap screws for easy installation to your track!Track is not included.Designed by a USCG charter captainManufactured proudly in the USA
Rod Boss Trbp Track Backing Plate, Set Of 4 - Trbp - 767-Trbpf1
Designed by a USCG charter captainManufactured proudly in the USA
Rod Boss Tr72 72" Track Mount, End Caps Sold Separately - Tr72 - 767-Tr72F1
Rod Boss's standard 3" track comes in 6", 12", 18", 24", 36", 48", 60", and 72" lengths to cover your boat's desired application. The grooved track design allows you to slide rod holders, trees, marine electronics, and accessories into endless locations. Mounting Rod Boss's track to your boat is as simple as placing the track in the desired location on your boat, drilling holes aligning with the track, and tightening down the track to your boat. Designed by a USCG charter captainManufactured proudly in the USA
