Docking & Fendering
Tie Down Engineering Dock Side Mounting Base - Magma Grill Kettle - 86913 - 241-86913F1
This mounting bracket provides secure mounting support for Magma's Kettle grills. Requires 1 receiver.
Tie Down Engineering Dock Side Cross Beam Extension - 86934 - 241-86934F1
With the addition of the Cross Beam 28 Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet wide.
Tie Down Engineering Dock Side Cross Beam Extension - 86916 - 241-86916F1
With the addition of the Cross Beam 28 Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet wide.
Tie Down Engineering Dock Hardware - Washer Plate - 26409 - 241-26409F1
Commercial grade. Should be used with every Angle. Two required for each Angle. 1-1/2"L x 5"H.
Tie Down Engineering Dock Hardware - Washer Plate - 24284 - 241-24284F1
Standard grade. Should be used with every Angle. Two required for each Angle. 1-1/2"L x 5"H.
Tie Down Engineering Dock Hardware - Piling Hoop And Roller Assembly, Commercial Grade - 26415 - 241-26415F1
Piling hoop & roller intended for areas with a lot of wind, current or tidal action. Combines the Piling hoop (26412) and roller assembly (26414) to make up for the up and down movement. For pilings up to 12" in diameter.
Tie Down Engineering Dock Hardware - Outside Pipe Holder - 26411 - 241-26411F1
Commercial grade. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set required for attaching.
Tie Down Engineering Dock Hardware - Outside Pipe Holder - 24280 - 241-24280F1
Standard grade. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set required for attaching.
Tie Down Engineering Dock Hardware - Outside Corner/Male 10"L X 5"H - 26522 - 241-26522F1
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab.
Tie Down Engineering Dock Hardware - Outside Corner/Male 10"L X 5"H - 26418 - 241-26418F1
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab.
Tie Down Engineering Dock Hardware - Outside Corner/Male 10"L X 5"H - 25491 - 241-25491F1
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab.
Tie Down Engineering Dock Hardware - Outside Corner/Female 10"L X 5"H - 26521 - 241-26521F1
Standard grade. Two 1/2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner/Female 10"L X 5"H - 26400 - 241-26400F1
Commercial grade. Two 1/2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner End - 26523 - 241-26523F1
Standard grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner End - 26428 - 241-26428F1
Commercial grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 12-1/4"L x 5"H.
Tie Down Engineering Dock Hardware - Outside Corner End - 26402 - 241-26402F1
Commercial grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 10"L x 5"H.
Tie Down Engineering Dock Hardware - Inside Corner Pipe Holder, Commercial Grade - 26405 - 241-26405F1
Commercial grade. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set for attaching. 2" Pipe.
Tie Down Engineering Dock Hardware - Inside Corner Pipe Holder, Commercial Grade - 26404 - 241-26404F1
Commercial grade. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set for attaching. 2" Pipe.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26524 - 241-26524F1
Standard grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 2" holes.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26417 - 241-26417F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 3" holes.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26403 - 241-26403F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 2-1/4" holes.
Tie Down Engineering Dock Hardware - Inside Corner 8-1/4"L X 5"H - 26401 - 241-26401F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ Square holes.
Tie Down Engineering Dock Hardware - Inside Corner 10-1/2"L X 5"H With 2-1/4" Elongated Holes And Larger Brace, Commercial Grade - 26424 - 241-26424F1
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 10-1/2"L x 5"H w/ 2-1/4" holes & larger brace.
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Lag Bolt Set (8 Per Bag) - 24292 - 241-24292F1
Commercial grade bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. Size: 3/8" x 5".
Tie Down Engineering Dock Hardware - Hot Dipped Galvanized Lag Bolt Set (8 Per Bag) - 24289 - 241-24289F1
Standard grade bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. Size: 3/8" x 3".
